Tensile Properties of Cast Alloy IN625 in Relation to d Phase Precipitation

doi:10.1007/s40195-018-0772-y

Acta Metallurgica Sinica (English Letters) ›› 2019, Vol. 32 ›› Issue (4): 535-540.DOI: 10.1007/s40195-018-0772-y

• Orginal Article • Previous Articles

Tensile Properties of Cast Alloy IN625 in Relation to d Phase Precipitation

Yi-Qiang Mu^1,², Chang-Shuai Wang¹, Wen-Long Zhou², Lan-Zhang Zhou¹()

1 Institute of Metal Research, Chinese Academy of Science, Shenyang 110016, China
2 School of Materials Science and Engineering, Dalian University of Technology, Dalian 116024, China

Received:2018-03-26 Revised:2018-04-22 Online:2019-04-10 Published:2019-04-19
Contact: Zhou Lan-Zhang
About author:
Dr. Kun-Kun Deng was born in 1983 and was awarded Ph. D in Harbin University of Technology in 2011. After graduation, he worked in the College of Materials Science and Engineering, Taiyuan University of Technology. At the same time, he continued his research work on the design, fabrication and processing of advanced Mg-based material in. Now, he is the vice chairman of Youth Committee in Magnesium Alloy Branch of Chinese Materials Research Society. He was denoted as young academic pacemaker of Shanxi Province in 2018. He has held two projects of National Nature Science Foundation of China, one project of Specialized Research Fund for the Doctoral Program of Higher Education, one Project of International Cooperation in Shanxi and two projects of Natural Science Foundation of Shanxi. He has published more than 60 articles. The time cited is more than 840 (without selfcitations), and the H-index is 22. In addition, he has published one academic monograph and acquired eight Chinese patents.

Abstract

Abstract:

The relationship between the tensile properties and δ (delta) phase precipitation in cast alloy IN625 was investigated in this paper. Although the influences of δ phase on the mechanical properties have been pointed out in our previous work, the relationship is still not directly determined due to the coexistence of γ″ (gamma double prime) and δ precipitates. In order to exclude the effect from γ″ phase, various fractions of δ precipitates with few γ″ precipitates were obtained by a set of experimental alloys aging at 750 °C, and tensile tests were conducted in parallel. The results showed that both yield strength and ultimate tensile strength increased nearly in linear with increasing δ phase fraction, while the elongation was relatively and limitedly affected by δ precipitation when the area fraction of δ phase was above 10%.

Key words: δ Phase;, Cast alloy IN625, Tensile properties, Advanced ultra-supercritical (AUSC)

Yi-Qiang Mu, Chang-Shuai Wang, Wen-Long Zhou, Lan-Zhang Zhou. Tensile Properties of Cast Alloy IN625 in Relation to d Phase Precipitation[J]. Acta Metallurgica Sinica (English Letters), 2019, 32(4): 535-540.

Figures/Tables 8

Table 1 Nominal compositions of the experimental alloys (wt%) [23]

Alloy	Nb	Mo	Cr	C	Ni
3.15Nb	3.15	9	21.5	0.05	Bal.
3.8Nb	3.8	9	21.5	0.05	Bal.
4.5Nb	4.5	9	21.5	0.05	Bal.

Fig. 1 SEM micrographs of δ phases in the Nb series of alloys after aging at 750 °C for 1000, 5000 and 17,000 h

Fig. 2 TEM image of the δ phases and corresponding selected-area electron diffraction pattern (inset)

Fig. 3 δ Phase area fraction evolution as a function of aging time and Nb content after aging at 750 °C

Fig. 4 Relationship between ln[-ln(1-Aδ/As)] and lnt

Table 2 Parameters for precipitation kinetics of δ phase

Alloy	α	N
3.15Nb	4.47?×?10^-7	0.876
3.8Nb	3.51?×?10^-6	0.792
4.5Nb	2.57?×?10^-5	0.710

Fig. 5 Tensile properties at 700 °C of the Nb series of alloys aged at 750 °C for 0 h (as-solution-treated), 1000, 3000 and 5000 h

Fig. 6 a YS, b UTS, c EL variations plotted as a function of the δ phase area fraction, d the dislocation substructure around δ phase in the aged experimental alloys after tensile tests

References

[1]	R. Zhou, L. Zhu, Y. Liu, Z. Lu, L. Chen, X. Ma, J. Mater. Sci. 52, 6161(2017)
[2]	X. Song, L. Tang, Z. Chen, R. Zhou, J. Mater. Sci. 52, 4587(2017)
[3]	K. Nicol, Status of Advanced Ultra-Supercritical Pulverised Coal Technology (IEA Clean Coal Center, London, 2013)
[4]	P.D. Jablonski, J.A. Hawk, C.J. Cowen, P.J. Maziasz, JOM 64, 271 (2012)
[5]	A. Nair, S. Kumanan, in Proceedings of the International Conference on Advances in Production and Industrial Engineering 2015, NIT Trichy, India, 2015
[6]	F. Abe, Engineering 1, 211 (2015)
[7]	N. Lückemeyer, H. Kirchner, H. Almstedt, in Proceedings of ASME turbo expo 2012, Copenhagen, Denmark, June 11-15, 2012
[8]	J.A. Siefert, J.P. Shingledecker, J.N. DuPont, S.A. David, Sci. Technol. Weld. Joi. 21, 397(2016)
[9]	D. Castello, B. Rolli, A. Kruse, L. Fiori, Energies 10, 1734 (2017)
[10]	S. Floreen, G.E. Fuchs, W.J. Yang, inThe metallurgy of alloy 625. Superalloys 718, 625 and Various Derivatives, TMS—AIME, Warrendale, 1994, pp. 13-37
[11]	I.J. Moore, J.I. Taylor, M.W. Tracy, M.G. Burke, E.J. Palmiere, Mater. Sci. Eng., A 682, 402 (2017)
[12]	L.M. Suave, D. Bertheau, J. Cormier, P. Villechaise, A. Soula, Z. Hervier, J. Laigo, in MATEC Web of Conferences, EUROSUPERALLOYS 2014-2 nd European Symposium on Superalloys and their Applications, EDP Sciences, 2014
[13]	E.A. Lass, M.R. Stoudt, M.E. Williams, M.B. Katz, L.E. Levine, T.Q. Phan, Metall. Mater. Trans. A 48, 5547 (2017)
[14]	L.M. Suave, J. Cormier, P. Villechaise, A. Soula, Z. Hervier, D. Bertheau, J. Laigo, Metall. Mater. Trans. A 45, 2963 (2014)
[15]	M.D. Mathew, K.B.S. Rao, S.L. Mannan, Mater. Sci. Eng., A 372, 327 (2004)
[16]	J.S. Kim, H.W. Lee, Int. J. Electrochem.Sci. 10, 6454(2015)
[17]	S. Malej, J. Medved, B.?. Bati?, F. Tehovnik, M. Godec, Metalurgija 56, 319 (2017)
[18]	X.J. Di, X.X. Xing, B.S. Wang, Acta Metall.Sin. 50, 323(2014) (in Chinese)
[19]	M. Sundararaman, P. Mukhopadhyay, S. Banerjee, MTA 19, 453 (1988)
[20]	D.R. Muzyka, G.N. Maniar, Metals. Eng. Quart. 9, 23(1969)
[21]	A. Kumar, K.V. Rajkumar, T. Jayakumar, B. Raj, B. Mishra, J. Nucl. Mater. 350, 284(2006)
[22]	Y.T. Ding, Y.B. Gao, Z.Y. Dou, X. Gao, D.X. Liu, Z. Jia, Acta Metall.Sin. 53, 695(2017). (in Chinese)
[23]	Y.Q. Mu, C.S. Wang, W.L. Zhou, L.Z. Zhou, Metals 8, 86 (2018)
[24]	N.Y. Ye, M. Cheng, S.H. Zhang, H.W. Song, H.W. Zhou, P.B. Wang, J. Iron. Steel Res. Int. 22, 752(2015)
[25]	G.A. Rao, M. Kumar, M. Srinivas, D.S. Sarma, Mater. Sci. Eng., A 355, 114 (2003)
[26]	L.C.M. Valle, L.S. Araújo, S.B. Gabriel, J. Dille, L.H. Almeida, J. Mater. Eng. Perform. 22, 1512(2013)
[27]	F. Xu, Y. Lv, Y. Liu, B. Xu, P. He, Phys. Procedia 50, 48 (2013)
[28]	D.B. Witkin, P. Adams, T. Albright, in Proceedings of the SPIE LASE, International Society for Optics and Photonics, 2015, 93530B-93530B-12
[29]	A. Chatterjee, G. Sharmaa, R. Tewari, J.K. Chakravartty, Metall. Trans. A 46, 1097 (2015)
[30]	V. Shankar, K.B.S. Rao, S.L. Mannan, J. Nucl.Mater. 288, 222(2001)
[31]	W.C. Liu, M. Yao, Z.L. Chen, Metall. Trans. A 30, 31 (1999)
[32]	W.C. Liu, M. Yao, Z.L. Chen, S.G. Wang, J. Mater. Sci. 34, 2583(1999)
[33]	A.C. McLaren, J.A. Retchford, Phys. Stat. Sol. (b) 33, 657(1969)

Tensile Properties of Cast Alloy IN625 in Relation to d Phase Precipitation

RichHTML

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

Figures/Tables 8

References

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	Qinyuan Zheng, Yi Lu, Chengwu Zheng, Peng Liu, Tian Liang, Yikun Luan, Dianzhong Li. Improving Ductility of a 3Mn Medium-Mn Steel by Manipulating the Austenite Reversion Path [J]. Acta Metallurgica Sinica (English Letters), 2025, 38(9): 1583-1590.
[2]	Jiayu Wang, Ke Liu, Zhao Lei, Xing Li, Li Liu, Sujun Wu. Machine-Learning-Assisted Phase Prediction in High-Entropy Alloys Using Two-Step Feature Selection Strategy [J]. Acta Metallurgica Sinica (English Letters), 2025, 38(8): 1261-1274.
[3]	Noa Lulu-Bitton, Nissim U. Navi, Noam Eliaz. Tensile Properties of Electrochemically Hydrogenated As-Built, Hot Isostatic Pressed and Heat-Treated Electron Beam Melted Ti-6Al-4V Alloys [J]. Acta Metallurgica Sinica (English Letters), 2025, 38(10): 1711-1718.
[4]	Lan Zhang, Dao-Kui Xu, Bao-Jie Wang, Cui-Lan Lu, Shuo Wang, Xiang-Bo Xu, Dong-Liang Wang, Xin Lv, En-Hou Han. Mechanical Behavior and Failure Mechanism of an As-Extruded Mg-11wt%Y Alloy at Elevated Temperature [J]. Acta Metallurgica Sinica (English Letters), 2024, 37(6): 969-981.
[5]	Xiaoliang Jia, Guhui Gao, Xiaolu Gui, Chun Feng, R. D. K. Misra, Bingzhe Bai. Uncovering Microstructure-Property Relationship in Ni-Alloyed Fe-Mn-Al-C Low-Density Steel Treated by Hot-Rolling and Air-Cooling Process [J]. Acta Metallurgica Sinica (English Letters), 2024, 37(4): 713-725.
[6]	Chao Xia, Kexin Zhao, Xin Zhou, Yuqi He, Panpan Gao, Hengxin Zhang, Guangrui Gao, Fengying Zhang, Hua Tan. Effect of Microstructural Characteristics on Fracture Toughness in Direct Energy Deposited Novel Ti-6Al-4V-1Mo Alloy [J]. Acta Metallurgica Sinica (English Letters), 2024, 37(1): 119-131.
[7]	Sheng Cao, Hongyu Liu, Jin Jiang, Ke He, Binghua Lv, Hao Zhang, Lujie Zhang, Jingrong Meng, Hao Deng, Xiaodong Niu. Effect of Heat Treatment on Gradient Microstructure and Tensile Property of Laser Powder Bed Fusion Fabricated 15-5 Precipitation Hardening Stainless Steel [J]. Acta Metallurgica Sinica (English Letters), 2024, 37(1): 181-195.
[8]	Ji-Peng Zou, Xue-Mei Luo, Bin Zhang, Guo-Dong Liu, Hong-Lei Chen, Xiao-Fei Zhu, Wen-Ke Yang, Guang-Ping Zhang. Microstructure Evolution and Tensile Properties of the Al_x(CoCrNi)_100-_x Medium-Entropy Alloys [J]. Acta Metallurgica Sinica (English Letters), 2023, 36(12): 2045-2057.
[9]	Hua-Zhen Jiang, Qi-Sheng Chen, Zheng-Yang Li, Xin-Ye Chen, Hui-Lei Sun, Shao-Ke Yao, Jia-Huiyu Fang, Qi-Yun Hu. Microstructure and Size-Dependent Mechanical Properties of Additively Manufactured 316L Stainless Steels Produced by Laser Metal Deposition [J]. Acta Metallurgica Sinica (English Letters), 2023, 36(1): 1-20.
[10]	Yongxin Lu, Fan Luo, Zhen Chen, Jian Cao, Kai Song, Lei Zhao, Xueli Xu, Hongduo Wang, Wenya Li. Microstructure and Mechanical Properties of Graphene Reinforced K418 Superalloy by Selective Laser Melting [J]. Acta Metallurgica Sinica (English Letters), 2022, 35(9): 1477-1493.
[11]	Hui Wang, Biao Guo, Xuguang An, Yu Zhang. Influence of Cold-Rolling Reduction on Microstructure and Tensile Properties of Nuclear FeCrAl Alloy with Low Cr and Nb Contents [J]. Acta Metallurgica Sinica (English Letters), 2022, 35(12): 2101-2110.
[12]	Jie Cui, Tianjiao Luo, Yingju Li, Xiaohui Feng, Qiuyan Huang, Yuansheng Yang. Fluidity, Microstructure, and Tensile Properties of Sub-rapidly Solidified Mg-6Al-4Zn-xSn (x = 0, 0.6, 1.2, 1.8) Alloy [J]. Acta Metallurgica Sinica (English Letters), 2021, 34(9): 1265-1276.
[13]	Ling-Yang Yuan, Pan-Wen Han, Ghulam Asghar, Bao-Liang Liu, Jin-Ping Li, Bin Hu, Peng-Huai Fu, Li-Ming Peng. Development of High Strength and Toughness Non-Heated Al-Mg-Si Alloys for High-Pressure Die-Casting [J]. Acta Metallurgica Sinica (English Letters), 2021, 34(6): 845-860.
[14]	Linxu Li, Xiufang Gong, Changshuai Wang, Yunsheng Wu, Hongyao Yu, Haijun Su, Lanzhang Zhou. Correlation Between Phase Stability and Tensile Properties of the Ni-Based Superalloy MAR-M247 [J]. Acta Metallurgica Sinica (English Letters), 2021, 34(6): 872-884.
[15]	Chenfan Yu, Yuan Zhong, Peng Zhang, Zhenjun Zhang, Congcong Zhao, Zhefeng Zhang, Zhijian Shen, Wei Liu. Effect of Build Direction on Fatigue Performance of L-PBF 316L Stainless Steel [J]. Acta Metallurgica Sinica (English Letters), 2020, 33(4): 539-550.