Bending and Twisting Springback Prediction in the Punching of the &nbsp;Core for a Lattice Truss Sandwich Structure

Wenchun JIANG; Bin YANG; Xuewei GUAN and Yun LUO

doi:10.1007/s40195-012-0268-0

Acta Metallurgica Sinica (English Letters) >

2013 , Vol. 26 >Issue 3: 241 - 246

DOI: https://doi.org/10.1007/s40195-012-0268-0

Bending and Twisting Springback Prediction in the Punching of the Core for a Lattice Truss Sandwich Structure

Wenchun JIANG ,
Bin YANG ,
Xuewei GUAN and Yun LUO

Expand

State Key Laboratory of Heavy Oil Processing, College of Chemical Engineering, China University of Petroleum (East China), Qingdao 266555, China

Received date: 2012-12-20

Revised date: 2013-01-16

Online published: 2013-05-06

Supported by

National Natural Science Foundation of China (No.51105380), Doctoral Program of Higher Education of China (No.20100133120008), Natural Science Foundation of Shandong Province (No.ZR2010AQ002), Fundamental Research Funds for the Central Universities (No.10CX04030A) and Key Laboratory ofPressure System and Safety(MOE), East China University of Science and Technology.

Fold

Abstract

The finite element method was used to study the springback induced by the punching of the core. In order to simulate the springback accurately, a mixed isotropic-nonlinear kinematic hardening model is used to define the material mechanical behavior during plastic deformation. The effects of the friction coefficient, the plate thickness and the die radius have been investigated. The results show that the springback of the sheet with diamond hole is different from the homogenous sheet. Not only bending springback, but also a twisting springback along the truss is generated because of the non-uniform distribution of the bending stress along the truss length. The plate thickness should be around 1.3 mm with larger friction coefficient and smaller die radius, which is useful to decrease the bending and twisting springback.

Key words： Plate with diamond hole; Punch; Springback

Cite this article

Wenchun JIANG , Bin YANG , Xuewei GUAN and Yun LUO . Bending and Twisting Springback Prediction in the Punching of the Core for a Lattice Truss Sandwich Structure[J]. Acta Metallurgica Sinica (English Letters), 2013 , 26(3) : 241 -246 . DOI: 10.1007/s40195-012-0268-0

References

[1] W.G. Kooistra and H.N. Wadley, Mater. Des. 28 (2007) 507.

[2] T.D. Queheillalt and H.N.G. Wadley, Mater. Des. 30 (2009) 1966.

[3] Q.C. Zhang, Y.J. Han, C.Q. Chen and T.J. Lu, Sci. China E: Technol. Sci.52 (2009) 2147.

[4] Q.C. Zhang, A.P. Chen, C.Q. Chen and T.J. Lu, Sci. China E: Technol.Sci. 52 (2009) 2670.

[5] T.D. Queheillalt, G. Carbajal, G.P. Peterson and N.G.H. Wadley, Int. J.Heat Mass Transf. 51 (2008) 312.

[6] W.G. Kooistra, S.V. Deshpande and N.G.H. Wadley, Acta Mater. 52(2004) 4229.

[7] T.D. Queheillalt and N.G.H. Wadley, Mater. Sci. Eng. A 397(2005) 132.

[8] W.C. Jiang, H. Chen, J.M. Gong and S.T. Tu, Mater. Sci. Eng. A528 (2011) 4715.

[9] S. Chatti and N. Hermi, Comput. Struct. 89 (2011) 1367.

[10] K.P. Li, W.P. Carden and R.H. Wagoner, Int. J. Mech. Sci. 44(2002) 103.

[11] P. Xue, T.X. Yu and E. Chu, Int. J. Mech. Sci. 43 (2001) 1893.

[12] A.S. Asgari, M. Pereira, B.F. Rolfe, M. Dingle and P.D. Hodgson, J.Mater. Process. Technol. 203 (2008) 129.

[13] W. Gan and H.R. Wagoner, Int. J. Mech. Sci. 46 (2004)1097.

[14] S.H. Cheng, J. Cao and Z.C. Xia, Int. J. Mech. Sci. 49 (2007)267.

[15] H. Naceur, Y.Q. Guo, L.J. Batoz and C. Knopf-Lenoir, Int. J. Mech. Sci.43 (2001) 2407.

[16] Z.Q. Jiang, H. Yang, M. Zhan, X.D. Xu and G.J. Li, Mater. Des.31 (2010) 2001.

[17] K. Yilamu, R. Hino, H. Hamasaki and F. Yoshida, J. Mater. Process.Technol. 210 (2010) 272.

[18] H.R. Wagoner and M. Li, Int. J. Plast. 23 (2007) 345.

[19] A. Mkaddem and D. Saidane, J. Mater. Process. Technol. 189(2007) 325.

[20] S.H. Kim and M. Koc, J. Mater. Process. Technol. 204 (2008)370.

[21] G. Ingarao, D.R. Lorenzo and F. Micari, Mater. Des. 30 (2009)4421.

[22] E. Daxin and Y.F. Liu, Mater. Des. 31 (2010) 1256.

[23] R. Kazan, M. Firat and E.A. Tiryaki, Mater. Des. 30 (2009) 418.

[24] S. Thipprakmas, Mater. Des. 31 (2010) 1593.

[25] I.N. Chou and C. Hung, Int. J. Machine Tools Manuf. 39 (1999)517.

[26] Y.E. Ling, H.P. Lee and B.T. Cheok, J. Mater. Process. Technol.168 (2005) 296.

[27] S.K. Panthi, N. Ramakrishnan, M. Ahmed, S.S. Singh and M.D. Goel,Mater. Des. 31 (2010) 657.

[28] A. Taherizadeh, A. Ghaei, E.D. Green and W.J. Altenhof, Int. J. Mech.Sci. 51 (2009) 314.

[29] D.J. Zhang, Z.S. Cui, X.Y. Ruan and Y.Q. Li, Comput. Mater. Sci.38 (2006) 256.

[30] F.W. Brust, T. Zhang, D.J. Shim, S. Kalyanam and G. Wilkowski,Proceedings of the ASME 2010 Pressure Vessels & Piping Division,Bellevue, Washington, USA, July 18-22, 2010.

[31] O. Muransky, C.J. Hamelin, M.C. Smith, P.J. Bendeich and L.Edwards, Comput. Mater. Sci. 54 (2012) 125.

[32] W.C. Jiang, J.M. Gong and S.T. Tu, Mater. Des. 31 (2010) 2157.

[33] W.C. Jiang, J.M. Gong and S.T. Tu, Mater. Des. 31 (2010) 2387.

Options

Outlines

模态框（Modal）标题

Abstract

Cite this article

References