In situ observation and thermodynamic calculation of MnS in 49MnVS3 non-quenched and tempered steel

  • LUO Yan-Zhao
Expand
  • School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China

Received date: 2010-12-07

  Revised date: 2011-03-02

  Online published: 2011-08-18

Abstract

Based on thermodynamics calculation, the results of the formation temperature of MnS inclusions of non-quenched and tempered steel during heating process were discussed. It is shown that while the solid fraction is 0.9, MnS inclusions began to precipitate in the final stage of solidification. The solidification process of 49MnVS3 non-quenched and tempered steel during heating has been observed in situ using a confocal scanning laser microscope (CSLM), which agrees well with the thermodynamics calculation. MnS particles were coarsening during heating process, which would reduce the pinning effect on the austenite grain boundaries and bring about the sudden growth of some austenite grains in this stage.

Cite this article

LUO Yan-Zhao . In situ observation and thermodynamic calculation of MnS in 49MnVS3 non-quenched and tempered steel[J]. Acta Metallurgica Sinica (English Letters), 2011 , 24(4) : 326 -334 . DOI: 10.11890/1006-7191-114-326

References

[1] S.R. Collins and G.M. Michal,  Metall Mater Trans A  24A  (1993) 2701.

[2] L.E. Iorio and W.M. Garrison,  ISIJ Int  42  (2002) 545.

[3] M.E. Valdez, Y. Wang and S. Sridhar,  Steel Res  76  (2005) 306.

[4] H. Takada, I. Bessho and T. Ito,  Tetsu-to-Hagane 18  (1978) 564.

[5] C.E. Cicutti, J. Madias and J.C. Gonzalez,  Ironmaking and Steelmaking  24  (1997) 155.

[6] M. Wintz, M. Bobadilla, J. Lehmann and H. Gaye,  ISIJ Int  6  (1995) 715.

[7] T. Yamashita, S. Torizuka and K. Nagai,  ISIJ Int  11  (2003) 1833.

[8] Z.B. Yang,  PhD Dissertation  (University of Science and Technology Beijing, Beijing, 2008).

[9] E.B. Yue,  PhD Dissertation  (China Iron and Steel Research Institute, 2004).

[10] E.T. Turkdogan,  Fundamentals of Steelmaking  (The University Press, Cambridge) p.298.

[11] H.B. Yin, K. Blazek and O. Lanzi,  ISIJ Int  10  (2009) 1561.

[12] N. Yuki, H. Shibata and T. Emi,  ISIJ Int  4  (1998) 317.

[13] Y. Kashiwaya, Y. Yamaguchi, H. Kinoshita and K. Ishii,  ISIJ Int  2  (2007) 226.

[14] D.N. Crowther, P.S. Mitchell and W.B. Morrison,  Proc 39th MWSP Conference  (Indianapolis, USA, 1997).

[15] E.J. Palmiere, G.I. Garcia and A.J. DeArdo,  Metall Mater Trans A  27A  (1996) 951.

[16] S. Morito, H. Saito, T. Furuhara and T. Maki,  ISIJ Int  45  (2005) 91.

[17] R. Priestner,  Mater Sci Forum   284  (1998) 95.

[18] X.J. Shao, X.H. Wang and W.J. Wang,  J Univ Sci Technol Beijing  5  (2010) 570.

[19] Z. Guo, N. Kimura, S. Tagashira, T. Furuhara and T. Maki,  ISIJ Int  42  (2002) 1033.
Outlines

/